ASTM B571 Test Guide: Peel Testing for Metals
PeelGrind the chisel edge to the exact specified angle and sharpen regularly to maintain uniform shear force application.
Testing Applications
Browse validated testing configurations. Filter by regulatory standard, material type, or force requirements.
20 items found
-
-
ASTM C273 Test Guide: Shear Testing for Composites
ShearAlways sandblast and solvent-wipe the steel loading plates to bare metal immediately before applying epoxy to prevent premature bond line…
-
ASTM D1000 Test Guide: Peel Testing for Tape
PeelAlways roll the tape onto the steel plate with a standardized mechanical roller at a uniform speed to eliminate manual…
-
ASTM D1002 Test Guide: Lap Shear Testing for Adhesives
ShearAlways insert spacer shims equal to the coupon thickness into the grips to guarantee a perfectly straight axial line of…
-
ASTM D2979 Test Guide: Peel Testing for Adhesives
PeelClean the stainless steel probe tip with reagent-grade toluene or isopropyl alcohol and a lint-free wipe before every single stroke.
-
ASTM D3163 Test Guide: Shear Testing for Adhesives
ShearAlways insert thickness-matching spacers into the grip jaws behind the specimen tabs to keep the bond line perfectly collinear with…
-
ASTM D3165 Test Guide: Shear Testing for Adhesives
ShearMeasure notch separation distance with an optical micrometer to the nearest 0.05mm to secure perfect shear area parameters.
-
ASTM D3330 Test Guide: Peel Testing for Tape
PeelMeticulously clean the stainless steel test plate with diacetone alcohol or n-heptane and a lint-free wipe before every single strip…
-
ASTM D3518 Test Guide: Characterization Testing for Composites
ShearYou must gather both longitudinal and transverse strain simultaneously; in-plane shear strain equals axial strain minus transverse strain.
-
ASTM D3528 Test Guide: Peel Testing for Adhesives
ShearVerify that the two lap joints are identical in surface area and bond line thickness to protect the mechanical symmetry…
-
ASTM D3846 Test Guide: Shear Testing for Composites
ShearVerify that the machined notches pass exactly halfway through the specimen thickness to isolate a clean, center-plane shear field.
-
ASTM D429 Test Guide: Peel Testing for Elastomers
PeelMeticulously document the exact failure mode split: R (Rubber Failure), RC (Rubber-Cement), CP (Cement-Primer), or M (Metal Interface).
-
ASTM D4501 Test Guide: Shear Testing for Adhesives
ShearEnsure the shearing tool blade rests perfectly flat against the step edge and is collinear with the bond line plane…
-
ASTM D5169 Test Guide: Shear Testing for Fasteners
ShearAlways use a calibrated 4.5kg weighted roller running at a consistent speed to mate the hook and loop sections; never…
-
ASTM D5379 Test Guide: Shear Testing for Composites
ShearAlways apply two cross-axial strain gauges mounted at $pm$45 degrees relative to the loading axis within the notch zone to…
-
ASTM D5868 Test Guide: Lap Shear Testing for Composites
ShearAlways insert thickness-matching spacer tabs behind the specimen inside the grips to keep the adhesive bond line perfectly aligned with…
-
ASTM D6117 Test Guide: Shear Testing for Plastics
ShearEnsure the fastener is driven perfectly perpendicular to the plastic lumber face using a mechanical drill press guide to prevent…
-
ASTM D732 Test Guide: Shear Testing for Plastics
ShearEnsure the center hole is drilled using a sharp, low-helix bit at slow feed rates to prevent micro-cracking and thermal…
-
ASTM D903 Test Guide: Peel Testing for Adhesives
PeelAlways discard the first 25mm of peeling data from calculations; adhesive failure must reach steady-state equilibrium before capturing valid averages.
-
ASTM E238 Test Guide: Shear Testing for Metals
ShearMeasure both the pin outer diameter and hole inner diameter to the nearest 0.01mm to document exact clearance values.