ASTM A370 Test Guide: Tensile Testing for Metals
TensileAlways use an extensometer rated for high-velocity shocks, and remove it immediately after yield if testing to failure.
Testing Applications
Browse validated testing configurations. Filter by regulatory standard, material type, or force requirements.
20 items found
-
-
ASTM B571 Test Guide: Peel Testing for Metals
PeelGrind the chisel edge to the exact specified angle and sharpen regularly to maintain uniform shear force application.
-
ASTM C1184 Test Guide: Tensile Testing for Adhesives
TensileClean and prime the substrate blocks precisely according to the manufacturer’s spec to isolate true sealant engineering limits.
-
ASTM C209 Test Guide: Tensile Testing for Wood
TensileWhen performing the perpendicular tensile test, use a high-strength epoxy to bond the metal blocks uniformly across the fiber face.
-
ASTM C297 Test Guide: Tensile Testing for Composites
TensileCure the bonded block assembly under a uniform dead-weight load to ensure a perfectly flat, parallel adhesive layer.
-
ASTM D1000 Test Guide: Peel Testing for Tape
PeelAlways roll the tape onto the steel plate with a standardized mechanical roller at a uniform speed to eliminate manual…
-
ASTM D1037 Test Guide: Tensile Testing for Wood
TensileAlways apply the static bending load to the natural molded face of the panel, and cross-reference thickness variations down to…
-
ASTM D2256 Test Guide: Tensile Testing for Yarns
TensileAlways apply the exact standard-specified pre-tension (typically 0.5 cN / tex) to remove structural slack before zeroing strain metrics.
-
ASTM D2979 Test Guide: Peel Testing for Adhesives
PeelClean the stainless steel probe tip with reagent-grade toluene or isopropyl alcohol and a lint-free wipe before every single stroke.
-
ASTM D3330 Test Guide: Peel Testing for Tape
PeelMeticulously clean the stainless steel test plate with diacetone alcohol or n-heptane and a lint-free wipe before every single strip…
-
ASTM D412 Test Guide: Tensile Testing for Elastomers
TensileNever use standard manual screw grips; vulcanized rubber narrows drastically under tension and requires self-adjusting pneumatic jaws.
-
ASTM D429 Test Guide: Peel Testing for Elastomers
PeelMeticulously document the exact failure mode split: R (Rubber Failure), RC (Rubber-Cement), CP (Cement-Primer), or M (Metal Interface).
-
ASTM D4325 Test Guide: Tensile Testing for Adhesives
TensileStore and condition tape rolls at standard atmospheric limits for exactly 24 hours prior to slitting or testing to equalize…
-
ASTM D4964 Test Guide: Tensile Testing for Fabrics
TensileCalibrate the precise initial distance between the roller axes using a solid reference spacer to guarantee an exact baseline loop…
-
ASTM D5766 Test Guide: Tensile Testing for Composites
TensileInspect the internal perimeter of the drilled hole under a microscope before testing; any evidence of fiber fraying or ply…
-
ASTM D638 Test Guide: Tensile Testing for Plastics
TensileAlways measure real specimen cross-section thickness at 3 distinct points before clamping; do not rely on nominal molded values.
-
ASTM D7269 Test Guide: Tensile Testing for Fibers
TensileAlways apply a minimal, uniform pre-load (~0.5 cN / tex) prior to starting the test loop to eliminate structural slack…
-
ASTM D882 Test Guide: Tensile Testing for Plastics
TensileAlways use a dual-blade specimen cutter to guarantee perfectly smooth, nick-free parallel edges; even a microscopic nick will act as…
-
ASTM D903 Test Guide: Peel Testing for Adhesives
PeelAlways discard the first 25mm of peeling data from calculations; adhesive failure must reach steady-state equilibrium before capturing valid averages.
-
ASTM E8 Test Guide: Tensile Testing for Metals
TensileAlways configure the closed-loop controller to run under automated strain-rate control (0.015 mm/mm/min) during the critical yield envelope.